Older NTM Machines: SSP MultiPro and Original SSQ Guide

Community guide · Updated · 8 min read

Buying an older NTM SSP MultiPro or original SSQ: years, controllers, how to tell versions apart, serial-number age checks, support and the risks.

Two older NTM roof panel machines still come up for sale: the SSP MultiPro, NTM’s first roof panel machine from 1991, and the original SSQ MultiPro, which NTM’s timeline dates to 2008. They suit a contractor who is comfortable doing their own maintenance and will check parts supply before buying. This guide covers how to tell the versions apart, how to check age, what NTM says about support, and the risks.

Quick facts

SSP MultiPro

  • Years: introduced 1991. NTM says it is no longer produced and does not publish the last year.
  • Profiles in the manual: SS150, SS550, SS675, SS200, SS210A and 3P.
  • Materials: painted, galvanized or aluminized steel to 22 gauge maximum, aluminum to .032″ maximum, and copper.
  • Panel width: 12″ to 24″ on SS150. Other profiles top out between 21-7/8″ and 24-3/4″.
  • Speed: about 60 ft/min.
  • Power: 16 hp electric-start gas engine, with a 220V 7.5 hp electric motor as the option.
  • Drive and shear: hydraulically driven polyurethane drive rollers and a hydraulic full-cycle shear (about 3 seconds per cycle).
  • Size and weight: about 12 ft long and about 2,000 lbs.

Original SSQ MultiPro

  • Years: 2008 on NTM’s timeline, with the SSQ II following in 2018. NTM publishes no end year.
  • Materials: painted steel 28 to 22 gauge, painted aluminum .019″ to .040″, copper 16 to 20 oz (3/4 hard), terne-coat stainless 26 gauge.
  • Profiles: NTM gives no count. The roller systems shown in the manual are listed further down.
  • Coil width: 15″ to 30″.
  • Speed: about 75 ft/min.
  • Drive and shear: hydraulic drive through chain, sprocket and gear to 16 polyurethane drive rollers, and a hydraulic shear with a panel-recognition sensor.
  • Size: 5′ wide, 4’3″ high with the reel rack or 1’10” without. Length is 14’3″ in one NTM manual and 13’7″ in the other.
  • Weight: 2,200 lbs, or 4,800 lbs on the trailer.

Which machine are you looking at?

Start with the model on the machine’s plate and the cover of the manual, then use these markers.

  • “SS-series” is not a machine. On NTM’s site, SS100, SS150, SS200, SS450, SS550 and SS675 are panel profile or roller-set names. If an ad says “SS-series”, ask the seller for the model shown on the plate.
  • SSP: NTM’s manual calls it the SSP Panformer. It is the shorter machine, about 12 ft, and its profile list is the short one given above.
  • Original SSQ or SSQ II: the original weighs 2,200 lbs against 2,830 lbs for the SSQ II. Its manual shows no BB750 board and batten profile. NTM lists its UNIQ touchscreen for the SSQ II, the SSQ3 and its WAV machine, not for the original SSQ.
  • Early or late original SSQ: machines made before April 2009 use a different slide-block arrangement for profile changes than later ones, and the manual shows both.

If the machine turns out to be an SSQ II, use our SSQ II buying guide instead.

SSP MultiPro in more detail

NTM still publishes the SSP manual. The spec table in that PDF is hard to read, so treat the length and weight above as approximate and measure before you plan transport.

The hydraulic reservoir holds about 20 gallons, and the manual recommends changing the fluid once a year. The decoiler is rated at 3,000 lbs with a 16″ or 20″ arbor.

Options listed in the manual were clip relief rollers, run-out stands, extra bead and striation rollers, a 12,000 lb tandem trailer with a dual overhead decoiler, and a “dual register” electronic control that measures length, shears and counts batches. Ask whether the machine has it.

Original SSQ in more detail

NTM publishes two manuals for the original SSQ, one for machines with an AMS controller and one for machines with a PLC controller. It does not publish the year it changed from one to the other. The standard setup in the manual is a 12V manual control box with a length-control limit switch, with computer batch and length control as the option.

The PLC manual shows these roller systems: SS100, SS150, SS450/SS450SL, FF100, FF150, BP100/BP150, SS200/SS210A, SS275, SS550, SS675, TRQ250, FWQ100 and FWQ150. NTM uses the same names today: SS100 and SS150 are mechanical seam, FF100 and FF150 are the slotted-flange snap-locks, and SS450 is a plain snap-lock.

The two manuals also differ on hydraulic fluid: about 15 to 16 gallons of 32AW in the PLC manual, 18 gallons in the AMS manual. Go by the manual that matches the controller on the machine.

Serial-number age check

NTM states that the last four digits of a machine’s serial number give the month and year it was built. Original SSQ serials are written with an SSQ prefix in the manual. NTM does not explain how that format lines up with the four-digit rule, so read the whole number to NTM and let them date it.

The serial also decides some repair procedures. The PLC manual splits shear troubleshooting at SSQ293xxx. Machines below that number have an adjustable shear pressure switch, and machines above it have an adjustable bottom-of-stroke limit switch.

The address on the plate is another clue. Older plates show Denver, and current NTM manuals show Aurora, Colorado. There is no public serial lookup. Call NTM Service at 303-294-0538, option 2, with the machine type, model number and serial number.

What NTM says about support and manuals

  • NTM lists the SSP manual and both original SSQ manuals under discontinued machine manuals on its site. The SSQ manuals are available in English and Spanish.
  • NTM’s FAQ says it keeps a broad parts inventory for all models, including older ones, and that parts are ordered through the Service team.
  • NTM’s own advice to used buyers is to contact the manufacturer and confirm parts and service for an older model before buying.
  • We found no NTM statement that sets an end date for SSP or original SSQ parts. That is not a guarantee, so ask about the specific parts you expect to need.
  • Free training comes with a new machine. On an older one, training and service are paid, and NTM says a technician may recommend paid service before training if the machine needs repair.
  • NTM’s service department can inspect or refurbish a used machine for a fee.

What to inspect and test

Use our used standing seam machine checklist for the full walk-around, and read the safety tips before you run a machine you do not know. On these two models, pay extra attention to the following.

  • Run every profile. Form and cut panels in each roller set included, in your gauge. Worn tooling shows up as wrong dimensions or a poor fit between panels.
  • Drive gears (original SSQ): NTM says drive gears are found only on the SSQ and SSQ II. They take open-gear spray lubricant. A broken drive gear or chain will stop the machine from driving.
  • Drive rollers: on a machine this age, check the polyurethane for separation and for sun or solvent damage.
  • Shear: ragged cuts or tearing mean dull or damaged blades.
  • Hydraulics: milky fluid has water in it, and dark fluid usually means a dirty filter. Check hoses and fittings for leaks. A machine that will not cut may have a broken or detached hose.
  • Controller: make a batch of panels and measure them. Ask NTM whether the controller on the machine is still supported.
  • Storage: look for rust, debris inside, missing covers and guards, and a dead battery on gas machines.

What should come with it

Ask for a written list: roller sets and shear dies by name, rib or bead rollers, reels or decoiler, run-out stands, the trailer, the controller and its cables, the printed manual, and any maintenance logs. The original SSQ on its trailer measures 17’6″ by 7′ by 6’3″.

Warranty

NTM’s three-year warranty is written for the original purchaser, so do not expect any of it on a machine this old. NTM’s FAQ describes a limited lifetime warranty against separation of the drive rollers, and its 2026 article on used gutter machines says that warranty does transfer to later owners. Ask NTM whether it applies to the machine you are considering.

The risks

  • Unknown history. Ask how it was stored, how often it ran and what problems it has had.
  • Age. NTM’s own lifespan figure is 20 to 30 years with regular maintenance and proper storage. An original SSQ built in 2008 is 18 years old in 2026.
  • Tested assemblies. If your panels must match a UL or wind-uplift tested assembly, the machine and tooling have to reproduce the tested profile.
  • Sellers. Read avoiding equipment scams before you send money to someone you have not met.

Buying or selling an older NTM

Older machines are listed with the rest on our New Tech Machinery page and under roll formers. If you have an SSP or an original SSQ sitting in the yard, you can post it free. Put the model, serial number, controller type and roller sets in the listing so buyers know which version it is.

Where these figures come from

The specifications in this guide were taken from New Tech Machinery’s published SSP and SSQ manuals, its company timeline and its support pages, as read in November 2026. This site is independent and is not affiliated with New Tech Machinery. For anything that matters, give NTM the machine’s serial number and confirm it with them.

Frequently asked questions

When was the NTM SSP MultiPro made?

NTM introduced the SSP in 1991 as its first roof panel machine and says it is no longer produced. NTM does not publish the last year of production. The manual, which calls the machine the SSP Panformer, is still on NTM's site under discontinued machine manuals. Use the serial number to date a specific machine.

How do I tell an original SSQ from an SSQ II?

NTM's timeline dates the original SSQ to 2008 and the SSQ II to 2018. The original weighs 2,200 lbs against 2,830 lbs, its manual has no BB750 board and batten profile, and its manuals cover an AMS or a PLC controller. Check the build date in the serial number and confirm the model with NTM Service.

Can I still get parts for an SSP or original SSQ?

NTM's FAQ says it keeps a broad parts inventory for all machine models, including older ones, ordered through its Service team. It has published no end date for SSP or original SSQ parts. NTM itself advises used buyers to call and confirm parts and service for an older model before buying, so ask about the specific parts you expect to need.

Are manuals available for discontinued NTM machines?

Yes. NTM lists the SSP manual and two original SSQ manuals, one for the AMS controller and one for the PLC controller, under discontinued machine manuals on its website. The SSQ manuals are offered in English and Spanish. Make sure you use the SSQ manual that matches the controller on your machine, since some figures differ.

What is an NTM SS-series machine?

There is no NTM machine by that name. On NTM's site, numbers such as SS100, SS150, SS450, SS550 and SS675 are panel profile or roller-set names, not machine models. If a listing says SS-series, ask the seller for the model and serial number on the machine's plate, then check both with NTM.

Have a question this guide didn't answer? Ask people who run these machines every day.

Ask the community