Buying a Used NTM SSQ II MultiPro: What to Check
What to know before buying a used NTM SSQ II MultiPro: its 16 profiles, materials, power packs, controllers, and what its 2026 discontinuation means.
The SSQ II MultiPro is the NTM machine for contractors who run panels full time: commercial jobs, large residential work, in-plant panel supply, and anyone who needs wall, soffit or tall-seam profiles from one machine. NTM discontinued it on September 30, 2026 and replaced it with the SSQ3 MultiPro, so every SSQ II for sale is now a used machine. This guide covers what the SSQ II runs, how it was configured, and what to check before you pay for one.
Quick facts
- Status: listed by NTM as discontinued (September 30, 2026). NTM’s company timeline dates the SSQ II to 2018.
- Profiles: 16, each with its own roller set.
- Steel: 28 to 22 gauge painted, galvanized or aluminized, 50 ksi maximum at 24 to 22 gauge.
- Other metals: copper 16 to 20 oz (3/4 hard), terne-coated stainless 26 gauge, painted aluminum up to .040″.
- Widths: coil 15″ to 30″, finished panel 12″ to 24″.
- Speed: about 75 ft/min on the gas engine, about 72 on 3-phase 60 Hz electric, about 50 on single-phase 60 Hz.
- Power: swappable Quick-Change Power-Pack, 16 HP Briggs & Stratton gas or a 5 or 7.5 HP electric motor.
- Drive and shear: hydraulic drive through 16 polyurethane drive rollers, hydraulic post-cut shear.
- Size: 14’4″ long (15’4″ with the angled slitter), 5’2″ wide, 4’3″ high with the overhead rack or 2’6″ without.
- Weight: 2,830 lbs for the base machine with one roller set, power pack and rib rollers. About 5,090 lbs on NTM’s trailer.
What “discontinued” means for a used buyer
Discontinued does not mean abandoned. NTM’s Service Hub still carries an SSQ II owner page with manuals, videos and a service request form, and NTM’s FAQ says it keeps a broad parts inventory for all models, older ones included. What NTM has not published is how long SSQ II parts will be stocked. Ask that question directly before you buy.
The SSQ3 forms the same 16 profiles, and its manual lists the same length, weight, top speed, coil range and steel gauges. The changes are in daily use: lever-clamp QWIKSwap tooling with a stated 25-minute changeover, sealed drive gear covers with inspection windows, and remote grease fittings.
The SSQ3 manual covers removing “legacy” bolted rails, which suggests SSQ II style rails can run in an SSQ3. NTM does not say whether QWIKSwap rails fit an SSQ II, so ask before you count on adding profiles later.
The 16 profiles
NTM’s names matter, because sellers mix them up. SS100 and SS150 are mechanical seam profiles, not nail strip. The nail-strip style panels, with a slotted fastening flange, are FF100 and FF150.
- Mechanical seam: SS100 (1″), SS150 (1.5″), SSQ200 (2″), SSQ210A (2″ ARMCO), TRQ250 (2.5″ trapezoid).
- Snap-lock: SS450 and SS450SL (1.5″), SSQ550 (1.5″), SSQ675 (1.75″), FF100 (1″, slotted flange), FF150 (1.5″, slotted flange).
- Snap-lock or mechanically seamed: SSQ275 (2″).
- Wall and other: FWQ100 and FWQ150 flush wall, soffit and underdeck panels, BB750 board and batten, T-Panel.
A used machine forms only the roller sets that come with it, so the profile list in the ad is a large part of what you are paying for.
NTM’s stated changeover is 45 minutes or less for one person with a 1/2″ wrench: unbolt the tooling rails, bolt on the next set, reset the entry guides and swap the shear dies. SS100, SS150 and SS450/SS450SL share left-side rollers, and so do FF100 and FF150. Going to or from BB750, SSQ275, SSQ550 or SSQ675 also means changing the #1 shear blade.
Materials and coil
NTM’s sources differ on thin aluminum. The manual gives painted aluminum from .019″ to .040″, while the product page starts at .027″. The manual also warns that some profiles have narrower limits, shown on each profile drawing. A 30″ coil needs an expandable arbor or a remote decoiler.
Power packs and hydraulics
The power pack comes off with two bolts, one communication cable and two hydraulic quick-disconnects. It weighs up to about 160 lbs, so plan on two people. Electric packs were offered in 220V single-phase (5 HP), 220V 3-phase (7.5 HP) and 460V 3-phase (7.5 HP). Check the pack on the machine against the power you have at your shop and on your jobs. The hydraulic system holds about 15 to 16 gallons of 32AW fluid and is factory set at 2,000 psi.
Controllers and options you may find
The manual lists a manual control box with a length-control limit switch as standard and computer batch and length control as an option. Later machines may carry NTM’s UNIQ panel, dated 2021 on NTM’s timeline, in a manual version or an automatic version with a 7″ touchscreen. The automatic UNIQ runs the drive, shear and notcher, takes cut lists typed in or loaded by USB, and stores up to 600 panel lengths. NTM says a manual UNIQ panel can be upgraded to automatic. An NTM service article also names the SSQ II among its PLC-controlled machines, so a used one may have either system.
Notching was an option and requires UNIQ. The angled slitter, also optional, cuts from 90 down to 35 degrees on notched panels up to 24″ wide.
What to inspect and test
NTM’s own advice to used buyers is to see the machine in person and run material through every profile and size it can make. For a general walk-through, use our used standing seam machine checklist along with the SSQ II points below.
- Drive rollers: look for polyurethane separating from the hub, cuts and chemical damage. A stripe the width of a roller on the panel means dirty rollers. Solvents ruin polyurethane, and so does sunlight if the machine sat without covers.
- Drive gears and chains: the three main drive gears need open-gear spray about every 30 operating hours, and the #50 chains need lube about every 40.
- Shear: cut several panels in each profile. Ragged or torn edges point to dull or dry blades. A crushed leg at the cut means the blade points are out of position or the dies ran dry. A leg catching the exit die is usually a die adjustment, not a new part.
- Entry guide and camber: a panel that runs uphill or downhill can come from an unlevel trailer, run-out stands at the wrong height, or a camber station that needs adjusting. Oil canning can come from an entry guide not set to the exact coil width.
- Hydraulics: the fluid should be clear. Milky means water, dark usually means a dirty filter, foamy means low oil or air. Check every hose and fitting for leaks.
- Controller and covers: run a short cut list and measure the panels. Wrong lengths point to a dirty or failed encoder wheel, a bad cable or calibration. Lift a cover and confirm the machine drops into maintenance mode.
Checking age by serial number
NTM states that the last four digits of the serial number give the month and year the machine was built. With the SSQ II on NTM’s timeline from 2018 and discontinued in 2026, the build date should fall in that span. NTM has no public serial lookup. Call NTM Service at 303-294-0538, option 2, with the machine type, model and serial number, and ask what they can tell you about that machine and its parts.
What should come with it
A used machine cannot be configured to order, so get the included items in writing:
- Each roller set by NTM name, with its matching shear dies and, where needed, the #1 shear blade.
- Rib rollers. One pair of bead, pencil, striation or V-rib rollers came standard.
- The power pack type, and whether a second pack is included.
- Overhead reel rack, expandable arbors or a free-standing decoiler (32″ maximum coil diameter on the rack, 45″ on the decoiler). The manual gives two different per-reel weight limits, so confirm capacity with NTM.
- Run-out tables, a cover and the trailer (NTM’s is a 12,000 lb tandem axle with electric brakes). If there is none, see roll former trailers.
- Manuals, maintenance logs and service records.
Warranty for a second owner
New SSQ IIs carried a limited three-year parts and NTM in-house labor warranty, written for the original purchaser. NTM’s 2026 article on used gutter machines says the three-year warranty does not pass to a second owner, while the lifetime warranty against drive roller separation does. An older NTM article says only that the warranty may not transfer. Plan on having no factory warranty and ask NTM about the specific machine.
Is a used SSQ II the right machine?
If you only run 1″ and 1.5″ residential panels, a smaller machine may do the job. Our SSQ vs SSH vs SSR comparison lays out the differences, and the guide to older NTM machines covers the original SSQ that came before this one. Current listings are on the New Tech Machinery page. If nothing there fits, post a wanted ad.
Own an SSQ II you no longer run enough to justify? You can list it free. Name every roller set, the power pack and the controller in the ad.
Where these figures come from
The figures in this guide are taken from New Tech Machinery’s published SSQ II and SSQ3 manuals and product pages as read in November 2026. This site is independent and is not affiliated with New Tech Machinery. Confirm anything that matters to your purchase with NTM, using the machine’s serial number.
Frequently asked questions
Is the NTM SSQ II MultiPro still being made?
No. NTM lists the SSQ II MultiPro as discontinued as of September 30, 2026 and now builds the SSQ3 MultiPro in its place. NTM still keeps an SSQ II owner page with manuals, videos and a service request form, and says it stocks parts for older models. It has not published how long SSQ II parts will be kept.
How many profiles can an SSQ II run?
NTM lists 16 profiles, from 1" and 1.5" mechanical seam and snap-lock panels up to 2" seams, a 2.5" trapezoid, flush wall and soffit panels, board and batten, and T-Panel. Each profile needs its own roller set and shear dies. A used machine only makes the profiles whose tooling is included in the sale.
What gauge steel will an SSQ II form?
The manual lists painted, galvanized or aluminized steel from 28 to 22 gauge, with a 50 ksi limit at 24 to 22 gauge. It also runs 16 to 20 oz copper, 26 gauge terne-coated stainless and painted aluminum up to .040". The manual notes that some profiles have narrower limits, shown on the profile drawings.
Will SSQ3 QWIKSwap tooling fit an SSQ II?
NTM does not say. The SSQ3 manual describes running older bolted tooling rails in an SSQ3, but nothing NTM publishes confirms that the SSQ3's lever-clamp QWIKSwap rails fit an SSQ II. If you plan to add profiles after you buy, ask NTM Service which roller sets are available for your serial number.
How do I tell how old an SSQ II is?
NTM says the last four digits of the serial number are the month and year the machine was built. The SSQ II appears on NTM's timeline from 2018 and was discontinued in 2026. There is no online lookup, so call NTM Service with the machine type, model and serial number to confirm.
Have a question this guide didn't answer? Ask people who run these machines every day.