NTM SSQ II and SSQ3 vs SSH vs SSR MultiPro Jr. Compared
NTM's SSQ II and SSQ3, SSH and SSR MultiPro Jr. compared on profiles, gauge, panel width, speed, power and controls, so you can pick the right size.
NTM builds its portable standing seam machines in three sizes: the SSR MultiPro Jr., the SSH MultiPro, and the SSQ (the SSQ II, discontinued on September 30, 2026, and the SSQ3 that replaced it). All three form the common 1″ and 1.5″ residential profiles, and they differ on almost everything else. This guide compares them on profiles, metal, power and crew so you can pick the size that fits your work.
Quick facts
- SSR MultiPro Jr.: 7 profiles, plug-in electric, manual shear, about 30 ft/min, 1,715 lbs.
- SSH MultiPro: 7 profiles, hydraulic drive and shear, about 60 ft/min, 2,360 lbs.
- SSQ II and SSQ3: 16 profiles, hydraulic drive and shear, up to about 75 ft/min on gas, 2,830 lbs.
- Steel: 28 to 24 gauge on the SSR and SSH, 28 to 22 gauge on the SSQ machines.
- Other metals: all three run painted aluminum up to .040″ and 16 to 20 oz copper.
- Finished panel width: 12″ to 16″ (SSR), 12″ to 20″ (SSH), 12″ to 24″ (SSQ).
- On NTM’s trailer: 3,975 lbs, 4,620 lbs and 5,090 lbs. NTM lists the same trailer footprint for all three, 18’11” long by 7’2-1/2″ wide by 6’3″ high.
- NTM timeline: SSR 2001, SSH 2004, SSQ II 2018, SSQ3 2025.
Side by side
| Feature | SSQ II / SSQ3 | SSH | SSR Jr. |
|---|---|---|---|
| Profiles | 16 | 7 | 7 |
| Tallest seam | 2″ (2.5″ trapezoid) | 1.5″ | 1.5″ |
| Wall and soffit panels | Yes | No | No |
| Steel gauge | 28 to 22 | 28 to 24 | 28 to 24 |
| Coil width | 15″ to 30″ | 14″ to 24″ | 15″ to 20″ |
| Speed | About 75 ft/min (gas) | About 60 ft/min | About 30 ft/min |
| Drive | Hydraulic, gear driven, 16 drive rollers | Hydraulic, chain driven, 8 drive rollers | Electric, 8 drive rollers |
| Shear | Hydraulic | Hydraulic | Manual |
| Power | Gas, or electric 220V and up | Gas, or electric 220V and up | 120V or 220V electric |
| Controller | Manual box, UNIQ optional | Manual box or PLC | Push buttons, EZ-Counter optional |
| Notching | Optional | No | No |
SSR MultiPro Jr.: the plug-in machine
NTM describes the SSR buyer as a residential roofer new to roll forming, a budget buyer, a one-person or part-time operation, or a crew that wants plug-in electric power. The 1.5 HP motor runs on a 120V, 18 amp supply, with a 220V version available. There is no gas engine and no hydraulic system.
What you give up is speed and width. Panels stop at 16″ finished, the shear is pulled by hand, and length control is a limit switch or the optional EZ-Counter, which stores up to 50 lengths and makes one panel at a time. Details are in our SSR MultiPro Jr. guide.
SSH MultiPro: the same profiles with hydraulics
The SSH forms the same seven profiles as the SSR: SS100 and SS150 mechanical seam, SS450 and SS450SL snap-lock, FF100 and FF150 slotted-flange snap-lock, and T-Panel. The difference is how it makes them. Drive and shear are hydraulic, speed doubles, finished width goes to 20″, and the power pack can be a gas engine or an electric motor.
NTM places it with residential and light commercial roofers who want hydraulics and do not plan to move into wall panels or heavy commercial work. NTM’s product page calls a PLC batch and length controller standard, while the manual lists it as an option, so check each listing. See the SSH MultiPro guide.
SSQ II and SSQ3: 16 profiles and 22 gauge
The SSQ machines add what the smaller two cannot do: 1.75″ and 2″ snap-locks, 2″ and 2.5″ mechanical seams, flush wall and soffit panels, and board and batten. They are also the only ones rated for 22 gauge steel, 24″ finished panels, notching and an angled slitter. NTM’s fit is full-time commercial and large residential work, in-plant panel supply, and anyone who needs wall, soffit or tall-seam profiles.
SSQ II or SSQ3?
The SSQ II dates from 2018 on NTM’s timeline and was discontinued in 2026. The SSQ3 was introduced in October 2025 with the same 16 profiles and the same main specs, so any SSQ3 offered used is a recent machine. What changed is the tooling and upkeep: QWIKSwap rails with a stated 25-minute changeover (45 minutes or less on the SSQ II), sealed gear covers with inspection windows, remote grease fittings, RFID cover sensors and a shear warning strobe. Our SSQ II guide covers what the discontinuation means. An SSQ with a build date well before 2018 is probably the original SSQ (2008 on NTM’s timeline), an earlier and lighter machine, so confirm the model with NTM.
Five questions that pick the machine
- Which profiles do your customers buy? If the answer is 1″ or 1.5″ mechanical seam, snap-lock or nail-strip style panels, any of the three will make them. A 2″ seam, flush wall or board and batten means an SSQ.
- What gauge and width? 22 gauge steel means an SSQ. Panels wider than 16″ rule out the SSR, and wider than 20″ rules out the SSH.
- What power is on site? The SSR runs from a 120V circuit. The SSH and SSQ need a gas pack or electric service of 220V or higher. On single-phase electric the SSQ II slows to about 50 ft/min.
- How much panel, and how many hands? The SSR runs at about 30 ft/min and someone pulls the shear on every panel, which is why NTM aims it at part-time and one-person operations. The other two have a hydraulic shear and at least twice the speed.
- Do you need cut lists or notching? The UNIQ automatic controller on an SSQ takes cut lists by USB and stores up to 600 lengths, and it is required for notching.
Changeover times
NTM states 45 minutes or less for one person on the SSQ II and 25 minutes on the SSQ3. The SSH and SSR use the EZE-Change roller system. One NTM article gives under an hour for both, and another gives one to two hours for the SSH. Neither product page lists a time, so judge by watching a changeover on the machine you are buying.
What to inspect, model by model
On any of the three, run every roller set included in the sale and look hard at the polyurethane drive rollers, the chains and the cut edge. After that the weak points differ:
- SSR: no hydraulics to check. Focus on the motor, the switches at both ends, the #40 chains and the feel of the manual shear.
- SSH: chain driven, so look for stretched or dry chains. Check the hydraulic oil (clear is good, milky means water), hoses and the exit-end sensor that pauses the machine when a cut panel is not cleared.
- SSQ II: three main drive gears that need open-gear spray about every 30 operating hours, cover interlocks that should drop the machine into maintenance mode, and the controller. If a notcher is fitted, run it.
Serial numbers and age
NTM says the last four digits of the serial number are the month and year of build, on all of its machines. That matters more on the SSR and SSH, which have been in production for over twenty years, than on the SSQ II. NTM has no online lookup. Its Service team (303-294-0538, option 2) asks for machine type, model number and serial number.
What comes with each
A new SSR ships with a dual overhead reel rack, one expandable arbor and two run-out tables. On the SSH and SSQ, items such as the reel rack, arbors and trailer are listed separately, so a used one may or may not have them. All three came with one pair of rib rollers. In every case, ask for the roller sets by NTM name, the matching shear dies, the manuals and any service records.
Warranty
All three carry the same new-machine warranty: three years, limited, on parts and NTM in-house labor, for the original purchaser. NTM’s 2026 article on used gutter machines says this does not transfer to a second owner, while the lifetime warranty against drive roller separation does. An earlier NTM article said only that it may not transfer. NTM’s list of things that void coverage doubles as a set of questions for the seller: solvents on the drive rollers, an unlubricated shear, the wrong hydraulic fluid, non-NTM parts and unauthorized repairs.
Prices and next steps
We leave prices out of this guide because they move with steel costs and tariffs. Check current asking prices on the New Tech Machinery listings, and read our roll former pricing guide for what drives them. If the size you want is not listed, post a wanted ad.
Moving from one size to another? You can list your current machine free and let the sale help fund the next one.
Where these figures come from
Every figure above is drawn from New Tech Machinery’s manuals, product pages and comparison articles as they stood in November 2026. This site is an independent marketplace, not affiliated with New Tech Machinery. Use the serial number of the machine in front of you to confirm with NTM anything your decision depends on.
Frequently asked questions
What is the main difference between the NTM SSR, SSH and SSQ?
The SSR is a 120V electric machine with a manual shear, seven profiles and about 30 ft/min. The SSH forms the same seven profiles with hydraulic drive and shear at about 60 ft/min. The SSQ II and SSQ3 form 16 profiles, including 2" seams and wall panels, run 22 gauge steel and reach about 75 ft/min on gas.
Which NTM portable machine runs 22 gauge steel?
Only the SSQ machines. NTM rates the SSR and SSH for 28 to 24 gauge steel and the SSQ II and SSQ3 for 28 to 22 gauge. The SSQ machines are also the only ones that make finished panels up to 24" wide. The SSH stops at 20" and the SSR at 16".
How is the SSQ3 different from the SSQ II?
They form the same 16 profiles and share the same main specifications in NTM's manuals. The SSQ3 adds lever-clamp QWIKSwap tooling with a stated 25-minute changeover, against 45 minutes or less on the SSQ II, plus sealed gear covers, remote grease fittings, RFID cover sensors and a shear warning strobe. The SSQ II was discontinued on September 30, 2026.
Can the SSH or SSR notch panels?
No. NTM lists notching and the angled slitter for the SSQ II and SSQ3 only, and a notching SSQ II needs the UNIQ automatic controller. The SSH has no notching option and does not take UNIQ. The SSR uses push buttons with an optional EZ-Counter length controller. If you need notched panels, look at an SSQ.
Which NTM machine suits a small residential crew?
NTM points the SSR at residential roofers new to roll forming, one-person and part-time operations, and crews that want plug-in power. It suggests the SSH for residential and light commercial roofers who want hydraulics, and the SSQ for full-time commercial work, in-plant panel supply and anyone needing wall, soffit or tall-seam profiles.
Have a question this guide didn't answer? Ask people who run these machines every day.