Used NTM SSR MultiPro Jr. Roll Former Buying Guide
How to buy a used NTM SSR MultiPro Jr.: the 120V electric roof panel machine, its profiles and limits, what to inspect, and what should come with it.
The SSR MultiPro Jr. is NTM’s entry-level roof panel machine: electric only, no hydraulics, and a shear you pull by hand. NTM points it at residential roofers new to roll forming, one-person and part-time operations, and crews that want to plug in and run. This guide covers what a used SSR can form, its limits, and how to check one before you buy.
Quick facts
- Status: current model, on NTM’s company timeline since 2001.
- Profiles: up to 7, all with 1″ or 1.5″ seams.
- Steel: 28 to 24 gauge, 50 ksi maximum at 24 gauge.
- Other metals: painted aluminum .027″ to .040″, copper 16 to 20 oz (3/4 hard).
- Widths: coil 15″ to 20″, finished panel 12″ to 16″.
- Speed: about 30 ft/min. Noise level under 70 dB(A).
- Power: 1.5 HP electric motor, 120V, 60 Hz, single phase, 18 amps. A 220V version exists. No gas option.
- Drive and shear: electric drive through chain, sprocket and gears to 8 polyurethane drive rollers. Manual forward-pulling rack and gear shear.
- Size: 12’6″ long, 3’10” wide, 4’3″ high with the overhead rack or 1’10” without.
- Weight: 1,715 lbs for the base machine, 3,975 lbs on NTM’s trailer.
A simpler machine, with trade-offs
NTM gives three reasons the SSR sits at the bottom of its range: it is electric only, the shear is manual, and the footprint is smaller. For a used buyer the first point is the big one. There is no pump, no hydraulic fluid, no hoses and no power pack to go wrong.
The trade-offs are just as plain. The SSR runs at about half the speed of NTM’s SSH. Somebody has to pull the shear on every panel. Finished width stops at 16″. There is no PLC or UNIQ controller and no notching. If you make panels a few days a month, none of that may matter. If you plan to run every day, compare it with the SSH MultiPro first.
Profiles and changeover
NTM lists up to seven profiles for the SSR:
- SS100 and SS150: mechanical seam, 1″ and 1.5″. These are not nail-strip panels, whatever the ad says.
- SS450 and SS450SL: 1.5″ snap-lock.
- FF100 and FF150: snap-lock with a slotted fastening flange, 1″ and 1.5″.
- T-Panel.
The SSR manual (Revision 12) shows roller systems named SSR100, SSR150, SSR450/450SL, FFR100 and FFR150, and has no T-Panel drawing. If T-Panel matters to you, ask NTM about tooling for the machine you are looking at.
Profile changes use NTM’s EZE-Change roller system plus a matching set of shear dies. One NTM article gives a changeover time of under an hour. The product page gives no figure. Check which roller sets you are getting and that the shear dies for each one are included.
Materials
Steel runs from 28 down to 24 gauge. NTM’s sources differ on one metal: the manual lists 26 gauge terne-coat stainless, and the product page does not. If you need terne, ask NTM before you count on it.
Power: check your cord and generator
The standard motor draws 18 amps at 120V, so the circuit, cord and generator all need to be sized for it. New machines shipped with a 100-ft 10-gauge cord. Ask whether that cord is still with the machine. NTM names the wrong extension cord gauge and an undersized generator among the things that can void its warranty, so ask the seller what the machine was run on. Also confirm whether you are looking at the 120V or the 220V version.
Controls
The standard setup is push-button RUN and JOG stations at the entry and exit ends, plus a length-control limit switch. The option is NTM’s EZ-Counter, a computerized length controller that holds up to 50 lengths and makes one panel at a time. Ask which one the machine has, and test it.
What to inspect and test
Ask the seller to have coil on the machine, then run panels in each profile included in the sale. NTM’s used-buying advice is to see every profile and size run before you pay. Our general guide on how to buy a used roll former covers the paperwork side. On the SSR itself, look at these:
- Drive chains: the SSR uses #40 roller chain, lubricated every 40 operating hours. Check for slack, rust and dry links.
- Drive roller pressure: NTM sets it at 1-3/4 turns past contact and allows no more than 1/2 turn extra. If the panel still slips inside that range, look for dirty rollers before anything else.
- Drive roller condition: the polyurethane should be bonded all the way around, with no cuts. Drive rollers are cleaned with soap and water only. Flat spots from sitting on a trailer usually work out with running, more slowly in cold weather.
- Forming rollers: look for rust, pitting and packed-in debris. NTM cleans these with a Scotch-Brite pad and a little solvent, kept off the drive rolls. Scratches or streaks on the paint come from chips or film stuck in the rollers.
- Manual shear: pull a cut on every profile. It should move smoothly and leave a clean edge. Ragged or torn cuts mean dull or dry blades. Make sure the dies match the roller set installed.
- Switches: try RUN and JOG at both ends, and check that the limit switch stops the panel where you set it.
- Entry guide: it has to be set to the exact coil width with the coil square to the machine. If not, you can get oil canning, camber or taper, and oil canning cannot be fixed after the panel is formed.
- Loose hardware: vibration loosens fasteners over time and lets forming stations shift. Rattles and poorly shaped panels are the signs.
Age by serial number
NTM has built the SSR since 2001, so a used one could be a few years old or more than twenty. NTM states that the last four digits of the serial number show the month and year of build. Get the full serial from the seller before you travel. There is no online lookup, so phone NTM Service (303-294-0538, option 2), give them the machine type, model and serial number, and ask about parts for that build.
What comes with it
A new SSR ships with a dual overhead reel rack, one expandable arbor and two 10-ft run-out tables. On a used one, check that all of that is still there. Then ask about:
- Roller sets and shear dies, by NTM name.
- Rib rollers. One pair came standard, and NTM’s options are bead, pencil, V-rib, striation and clip relief.
- The EZ-Counter, if fitted.
- A second arbor, a cover and the power cord.
- The trailer. Machine and trailer together measure 18’11” by 7’2-1/2″ by 6’3″. Our guide to moving and shipping roll formers covers the options if you are buying out of state.
- The manual and any maintenance records.
Maximum coil diameter is 32″ on the overhead rack and 45″ on a decoiler. We did not find a reel weight limit for the SSR in NTM’s published pages, so ask NTM before you hang a heavy coil.
Warranty for second owners
New SSRs are sold with a limited three-year parts and NTM in-house labor warranty. NTM’s terms word it for the original purchaser. Its most recent statement on the subject, in a 2026 article about used gutter machines, says the three-year warranty does not carry over to a second owner but the lifetime warranty against drive roller separation does. An older article says the warranty may not be transferable. Buy on the assumption that you have no factory coverage, and ask NTM if you want it confirmed for a particular serial number.
Where to look, and where to sell
Used SSRs show up on our New Tech Machinery page and in the wider list of used machines. To see how the SSR stacks up against NTM’s two larger models, read the SSQ vs SSH vs SSR comparison.
Outgrown your SSR, or not using it enough? You can list it here free, and a clear note of the voltage, roller sets and serial number will save you a string of phone calls.
Where these figures come from
These numbers were read from New Tech Machinery’s SSR manual and product pages in November 2026. This marketplace is independent and has no affiliation with New Tech Machinery. Before you rely on any figure, confirm it with NTM and quote the machine’s serial number.
Frequently asked questions
What power does the SSR MultiPro Jr. need?
The standard motor is 1.5 HP, 120V, 60 Hz, single phase, drawing 18 amps, and NTM also lists a 220V option. There is no gas engine version. New machines include a 100-ft 10-gauge cord. NTM warns that the wrong cord gauge or an undersized generator can void the warranty, so size both for the motor.
How fast is the SSR and how wide a panel does it make?
About 30 feet per minute, with finished panels 12" to 16" wide from coil 15" to 20" wide. For comparison, NTM's SSH runs about 60 feet per minute and makes panels up to 20" wide. The SSR's shear is manual, so the operator pulls every cut by hand.
Does the SSR have a hydraulic system?
No. The drive is electric, through chain, sprocket and gears to eight polyurethane drive rollers, and the shear is a manual rack and gear. That means no hydraulic fluid, pump, hoses or filter to maintain. NTM gives the lack of hydraulics, the manual shear and the smaller footprint as the reasons it is the lower-cost machine.
Is there a length controller on the SSR?
Standard controls are RUN and JOG push buttons at both ends with a length-control limit switch. NTM offers an optional EZ-Counter computerized length controller that holds up to 50 lengths and makes one panel at a time. PLC and UNIQ controllers are not available on the SSR, so check which setup a used machine has.
What should come with a used SSR?
A new SSR includes a dual overhead reel rack, one expandable arbor and two 10-ft run-out tables, plus one pair of rib rollers. On a used machine, confirm those are still present and ask about roller sets, shear dies, the EZ-Counter, the trailer, the power cord and the manual.
Have a question this guide didn't answer? Ask people who run these machines every day.