Used NTM SSH MultiPro Roof Panel Machine Buying Guide
A plain guide to buying a used NTM SSH MultiPro: the seven profiles it forms, gauges, power, controller types, and the checks to make before you pay.
The SSH MultiPro sits in the middle of NTM’s portable roof panel line. NTM aims it at residential and light commercial roofers who want a hydraulic drive and a hydraulic shear but do not expect to move into wall panels or heavy commercial work. This guide covers what a used SSH can form, where NTM’s own published figures disagree, and what to check before you hand over money.
Quick facts
- Status: current model, on NTM’s company timeline since 2004.
- Profiles: 7, with seam height topping out at 1-1/2″.
- Steel: 28 to 24 gauge painted (50 ksi maximum at 24 gauge).
- Other metals: painted aluminum .027″ to .040″, copper 16 to 20 oz (3/4 hard), terne-coat stainless 26 gauge.
- Widths: coil 14″ to 24″, finished panel 12″ to 20″.
- Speed: about 60 ft/min on every power source.
- Power: Quick-Change Power-Pack, 16 HP gas or a 5 or 7.5 HP electric motor.
- Drive and shear: hydraulic, chain driven, 8 polyurethane drive rollers, hydraulic shear.
- Weight: 2,360 lbs for the base machine with a roller set, power pack and rib rollers. 4,620 lbs on NTM’s trailer.
- Size: 4’3″ high with the overhead rack. NTM’s manual and product page give different lengths and widths (see below).
Seven profiles, none taller than 1.5″
Learn NTM’s profile names before you read ads, because the numbers do not mean what many sellers assume:
- SS100 and SS150: 1″ and 1.5″ mechanical seam.
- SS450 and SS450SL: 1.5″ snap-lock.
- FF100 and FF150: 1″ and 1.5″ snap-lock with a slotted fastening flange (the nail-strip style).
- T-Panel.
In the SSH manual the roller systems carry an H in the name: SSH100, SSH150, SSH450/450SL, FFH100 and FFH150. If a seller lists roller sets that way, those are the same panel profiles.
What the SSH does not do: 2″ seams, flush wall or soffit panels, board and batten, notching or an angled slitter. NTM lists those for the SSQ line only. If any of that is in your plans, read the used SSQ II guide before you settle on an SSH.
Changing profiles
NTM calls the SSH tooling system EZE-Change. You swap the tooling rails (right side first, then left) and the shear dies, using a 1/4″ Allen wrench and a torque-set wrench or impact, then check that the rails are parallel with a string. NTM’s articles do not agree on how long this takes. One says under an hour. Another says one to two hours, depending on how well the operator knows the machine.
If you are buying more than one roller set, ask the seller to change a profile in front of you. You will see the real time and whether every part is there.
Materials and coil
The SSH stops at 24 gauge steel. If customers ask you for 22 gauge panels, this is not your machine. At 24 gauge the limit is 50 ksi, and at 28 to 26 gauge NTM accepts 80 ksi with adjustments. Coil can be 14″ to 24″ wide, but a 24″ coil needs an expandable arbor or a free-standing decoiler.
Drive, hydraulics and power
NTM describes the SSH as chain driven, where the larger SSQ machines are gear driven. A hydraulic motor turns the eight drive rollers through #50 roller chain at the drive sprocket and #41 chain between the drive rolls. The hydraulic system holds 15 gallons of 32AW fluid and is factory set at 2,000 psi.
The power pack is swappable: a 16 HP Briggs & Stratton gas engine, or an electric motor of 5 or 7.5 HP in voltages from 220V to 460V. Find out which pack the machine has. An electric pack you cannot feed on a job site is a problem you will pay to solve.
Controller: expect either kind
NTM’s product page says a PLC batch and length controller with a touchscreen (up to 99 jobs) is standard. The manual’s spec page lists a 12V manual control box with a length-control limit switch as standard and the PLC as an option. On a used SSH you may find either one, so ask and look. NTM’s UNIQ control system is not offered on the SSH.
The PLC controller has its own serial plate, on the side connector plate of the controller case between the proximity and encoder plugs. Write that number down along with the machine’s serial number.
Size: measure it yourself
NTM’s two sources disagree on the footprint. The manual gives 13’1-1/2″ long by 3’10” wide, and 2’0″ high without the overhead rack. The product page gives 12’10” long by 4’10-1/2″ wide. If the machine has to fit a truck bed, a shop door or a container, put a tape on it. On NTM’s trailer the manual lists 18’11” by 7’2-1/2″ by 6’3″.
What to inspect and test
Run coil through every roller set that comes with the machine, in the gauge you plan to use. NTM puts that test ahead of everything else in its used-buying advice. Then work through the machine:
- Chains: on a chain-driven machine, chain care shows. The manual calls for lube every 40 operating hours with a dry chain lube. Chains stretch and need periodic tightening. Look for slack, rust and stiff links.
- Drive rollers: factory pressure is 3/4 turn past contact, with no more than 1/4 turn added if the rollers slip. Rollers cranked down harder than that suggest someone was fighting a feed problem. Check the polyurethane for separation, cuts and chemical damage.
- Shear: the manual wants the blades and dies lubricated daily, and NTM says not to use WD-40 on them. Jagged or uneven cuts, a panel catching the exit die, or a broken die point to a shear that is out of alignment or worn. Often it needs adjusting for the profile, not replacing.
- Hydraulic oil: the level should sit about 5″ below the filler neck, and the oil should be clear. Milky oil has water in it. Check hoses and fittings for leaks, and ask when the oil and filter were last changed (NTM says yearly).
- Exit sensor: the SSH has a proximity sensor at the exit end that pauses the machine if a cut panel is not cleared. Leave a panel in place and see that it works.
- Panel shape and length: lay a long panel flat. Camber can come from a trailer that is not level or run-out stands at the wrong height, so set up properly before you judge. Check panel length against the controller, since a dirty encoder wheel or a bad cable gives wrong lengths.
Our roll former maintenance guide explains the routine a careful owner would have followed.
Age by serial number
The SSH has been built since 2004, so age varies a lot from one listing to the next. NTM states that the last four digits of the serial number are the month and year of manufacture. Read the number off the machine yourself instead of relying on the ad. NTM does not run a public lookup. The route it describes is a call to its Service team (303-294-0538, option 2) with the machine type, model number and serial number. Ask whether parts for that build are in stock and whether the controller on it is still supported.
What comes with it
Two SSH machines at the same asking price can be very different packages. Ask for a list:
- Roller sets and matching shear dies, by name.
- Rib rollers. One pair came standard, and the options were bead, pencil, striation, V-rib and clip relief.
- Reels. The dual overhead rack carries 6,000 lbs total at 3,000 lbs per arbor, with a 32″ maximum coil diameter. The free-standing decoiler takes 5,000 lbs and a 45″ coil.
- Trailer, cover, remote control and run-out tables, if any.
- A second power pack, if the seller has both gas and electric.
- The machine manual, the controller manual and any service records.
Warranty for second owners
A new SSH comes with a limited three-year warranty on parts and NTM in-house labor, and NTM’s terms give it to the original purchaser. In a 2026 article on used gutter machines, NTM states that the three-year coverage does not pass to a second owner, though the lifetime warranty against drive roller separation does. An earlier article says only that it may not transfer. NTM’s sources also differ on whether the three years start at purchase or at the build date. Treat any remaining warranty as unconfirmed until NTM tells you otherwise for that serial number.
Finding one, or selling yours
SSH listings appear on our New Tech Machinery page and under standing seam roll formers. Not sure the SSH is the right size? The SSQ vs SSH vs SSR comparison puts the three side by side. Before you send a deposit to anyone, read avoiding equipment scams.
If you own an SSH and are thinking of moving up or down in size, you can post a listing at no charge. Include the roller sets, power pack, controller type and serial number, since buyers ask for those first.
Where these figures come from
Specifications here come from New Tech Machinery’s SSH manual and product pages, read in November 2026. We are an independent marketplace with no affiliation to New Tech Machinery. Where a detail affects your decision, check it with NTM and give them the serial number of the machine you are looking at.
Frequently asked questions
What profiles does the NTM SSH MultiPro make?
Seven: SS100 and SS150 mechanical seam (1" and 1.5"), SS450 and SS450SL 1.5" snap-lock, FF100 and FF150 snap-lock with a slotted fastening flange, and T-Panel. Seam height stops at 1.5". The SSH does not make flush wall, soffit or board and batten panels, which NTM offers on the SSQ machines.
Can the SSH run 22 gauge steel?
No. NTM rates the SSH for 28 to 24 gauge painted steel, with a 50 ksi limit at 24 gauge. It also lists painted aluminum from .027" to .040", 16 to 20 oz copper and 26 gauge terne-coat stainless. For 22 gauge steel you would need one of NTM's SSQ machines, which are rated from 28 to 22 gauge.
How long does a profile change take on an SSH?
NTM's own articles disagree. One says under an hour and another says one to two hours depending on operator experience. The job involves swapping the right and left tooling rails and the shear dies, then checking the rails are parallel with a string. Watch the seller do one before you buy extra roller sets.
Does a used SSH have a computer controller?
It may or may not. NTM's product page describes a touchscreen PLC batch and length controller holding up to 99 jobs as standard. The manual lists a manual control box with a length limit switch as standard and the PLC as an option. Check the machine itself. NTM's UNIQ controller is not offered on the SSH.
Does the NTM warranty transfer when I buy a used SSH?
Plan on it not transferring. NTM's terms give the three-year warranty to the original purchaser, and a 2026 NTM article says it does not pass to second owners, although the lifetime warranty against drive roller separation does. An older article says it may not transfer. Ask NTM about the specific serial number.
Have a question this guide didn't answer? Ask people who run these machines every day.